Synopsis Set of information and tools whilst working with my M3i Zero ( GMP-Z003 ) andits firmware.Hardware Flash Memory The GMP-Z003 uses a MX29LV160DBXEI-70G for flash memory, it is a 2MB chip.This device operates over a voltage range of 2.7V to 3.6V typically using a 3Vpower supply input.
![]() Flashing The device can be flashed by providing DC power to the J3 port. I just strippeda USB cable and put the positive and ground in. The FPGA searchesthe SD card for FCORE.DAT and copies 0x200000 - 0x400000 to the flashmemory chip. I believe the FCORE.DAT needs to be signed in order for theFPGA to copy it first however. The LED light D1 will change depending on the status of the flash: Nothing: No power or completed Static: Error reading FCORE.DAT (SD card might not be inserted, etc.) Flashing: Copying FCORE.DAT to the flash memory. Alternatively the device can be flashed whilst inserted via the DS itselfusing card commands. One sector (header ) is at 0x80000000 then the others start at offset 0. Changes Update the firmware of M3i Zero card, to support new 3DS consoles (Ver. J, Ver. 2.1.0-4U, Ver. E) Solve the SD card compatibility issue. Update procedure Copy the M3GUpdaterPlus143.nds onto the microSD card. M3I Zero Gmp Z003 Firmware Install The M3SAKURACopy the system file onto the microSD card or install the M3SAKURA system (For the detail of installing the system or M3SAKURA, please read the corresponding instruction.) Insert that microSD card into the M3i Zero card. M3I Zero Gmp Z003 Firmware Software Should RunInsert M3i Zero card into one of the following console (NDS, NDS Lite or NDSi NDSi(XL)) Power on the console and the M3 software should run up. Select the M3GUpdaterPlus143.nds file then press A to launch it. Just follow the instruction on the screen or press start twice to start the updated process. The Updating success message will be displayed on the screen if the updated process is success. After the updated process is finished, you may take out the M3i Zero, You may insert this card into 3DS to use it. M3I Zero Gmp Z003 Firmware Download Source CommentDownload Source Comment on: M3i Zero fix for DSi Firmware Upd.amp; 3DS Firmware Update 2.1.0-4 funkdat top options So does this update only work with M3i Zero GMP-Z003 and if not, should I even worry about it if I have a V1 M3i Zero that works just fine on my 3DS Comment on: M3i Zero fix for DSi Firmware Upd.amp; 3DS Firmware Update 2.1.0-4 Nathan top options It should only work with the GMP-Z003 model, so if your V1 model works fine, please disregard this update. Comment on: M3i Zero fix for DSi Firmware Upd.amp; 3DS Firmware Update 2.1.0-4 iceberg303 top options The v1 isnt getting any new FW updates, it does have a software update but not a fw update. In fact I can not get any response from the support team at all. Comment on: M3i Zero fix for DSi Firmware Upd.amp; 3DS Firmware Update 2.1.0-4 rabiancone top options Just to be clear: This fix will only install on DS Lite 1.4.3U, right Once installed you can use it on regular DSI 1.4.3U In other words, if you dont have DS Lite youre fuked 1 user(s) are viewing this topic (1 Guests) Powered by FunkySkunk Forums v2 2007 retrohead - Exclusive to DS-Scene.net - irc.efnet.net ds-scene Performed 9 Queries in 0.00352 Seconds. The page rendered in 0.71244 Seconds.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |